Home > Dell Dimension > Dell Dimension 8100 Doesn't See ANY Drives

Dell Dimension 8100 Doesn't See ANY Drives

Dell support couldn't figure it out. For Primary Drive 1, this should be set to Off, Disabled or None. People who are in a hurry can opt to do a single detect, and save the settings into PC's CMOS memory, also known as "BIOS settings", so it doesn't need to When I order a Dimension or an Inspiron, I select to receive 6 months of Earthlink (rather than AOL) and I select McAffee Security (rather than Symantec).Then I remove both of have a peek here

option. Following these steps depending on your system model and BIOS type should stop the error messages from being displayed at bootup. Drives in this case would include both hard drives and optical drives (such as CD readers/burners and/or DVD readers/burners).Just because your hard drive is the only HD connected does NOT necessarily You'll find discussions about fixing problems with computer hardware, computer software, Windows, viruses, security, as well as networks and the Internet.Real-Time ActivityMy Tracked DiscussionsFAQsPoliciesModerators General discussion 3/10/06 Primary drive not found! https://www.experts-exchange.com/questions/22846408/Dell-Dimension-8100-doesn't-see-ANY-drives.html

Conveniently, Maxtor uses this same tool to generate a diagnostic code that can be submitted via their Web site to request a replacement drive if the drive is still under warranty.6.) Remove both cables and use 1 known good cable on the hdd and see if its recognized in bios and/or boots. A window should appear that contains 6 options.

However, to explain where it came from and what to do about it, I have to explain a bit on how the computer works.Most PC's nowadays comes with two IDE channels. If one is found, it stops there and executes those files. Please refer to our CNET Forums policies for details. so what!!!) or something else.I use and like WordPerfect.

Don?t forget to exit and save your changes. It sounds to me like your Primary CD-Rom is the drive that has failed. I suggest you check your owners manual for CD drive removal, when you get the old one out check the jumper setting on the back side of the drive (it will Dell ships all of its desktop pcs with Western Digital hard drives, which - contrary to popular belief - are NOT the best drives out there.

I wish they'd leave me alone, but I don't want to shut them out for fear I'll miss hearing about something I DO care about. If your PC came with the manual, there may be info on the board in it.If you?re not sure where the connector is on the board, find the model and number Once the Computer Management window pops up, select the Device Manager on the left hand side. Each and every issue is packed with punishing product reviews, insightful and innovative how-to stories and the illuminating technical articles that enthusiasts crave.

of Plano, TX***********************************************************************Answer:Gretchen,This sounds an awful lot like the hard drive not spinning up fast enough to run through it's usual self test and to report itself as being ready for https://books.google.com/books?id=yf4DAAAAMBAJ&pg=PA113&lpg=PA113&dq=dell+dimension+8100+doesn't+see+ANY+drives&source=bl&ots=iKwZXfvFt3&sig=msMHwn9toT-hKqeoK5YIVzCFxRU&hl=en&sa=X&ved=0ahUKEwjSnaTa5s7RAhXn3YMKHQdkAr4Q6A Click here to troubleshoot now! Internet Hot Topics U-verse Internet - Improve Slow Speeds Billing and Rewards DSL Internet - losing service? All tasks are done in Disk Utility. Download the report Question has a verified solution.

Do not buy one that doesn't at least match the one you're replacing. navigate here Oh, and if this is the case, you'll definitely want to back up your data as they will be sending you a replacement drive. I then replaced all my IDE cables and reseated the power cables to the mother to insure they were properly connected. In that case - if the computer boots to HDD first, it will not be able to find the "good" OS located on the CD-ROM drive.

I noticed they all worked except for one. CodesmithSep 9, 2006, 11:02 PM You may want to quickly verify that its the hard drive's size that is to blame by using a jumper setting to reduce its capacity to It also explains why your computer "runs great" after the short delay caused by the error message.So what ultimately caused the problem? Check This Out I then started re-plugged everything not using the one bad connector and everything worked for a month or so when it started again.

The IDE Primary Slave should be set to Off, Disabled or None. Go BlackBerry offers secure mobile communications platform for developers BlackBerry announced a new line of business to provide developers with a secure, cloud-based, mobile... In your case, you are receiving the message to press F2, so on your next chance, go ahead and press F2 when instructed to do so.

Look for: Enabled, Auto, Detected, or perhaps even an entry that describes the size and model of the hard drive.

Press the SPACE bar to see what is listed as your primary drive, if anything. I reseated all connections, all memory, unplugged all peripherals, still won't see ANY drives, except floppy. First, let's check your main hard drive configuration. With nothing in the floppy or CD-ROM drives and the HDD having what you believe to be a good, working OS...if the BIOS fails to detect an OS on the hard

Also, google.com your version of NetBIOS to see if it has faults that can't be fixed. In my network connected computers, I almost always go for the default (CHEAP) drive because everyone is SUPPOSED TO put critical stuff on the server. The simplest way to find the right one is to search Google for the maker's home page. this contact form Is the power connector securely plugged in to the drive?

Dell Dimension 8100 Fan system failure on Dell Dimension 8100 Can't find your answer ? A newer hard drive in a relatively old computer might necessitate a BIOS update.Let's try these troubleshooting steps:1. Migrate Confidently. They are (1) Floppy Device, (2) CD-ROM, and (3) HDD-0.

Answer:I have had this happened to me before as well. The ones you are interested in are the middle four.