Dell Inspiron 1100 Won't Bootup
I tried taking the bottom screws off to take the machine apart but to no avail. Main Sections Technology News Reviews Features Product Finder Downloads Drivers Community TechSpot Forums Today's Posts Ask a Question News & Comments Useful Resources Best of the Best Must Reads Trending Now I only removed the memory from slot "A" to slot "B". Just go into the BIOS setup and set the batter mode settings to all the max settings. have a peek here
I hope it helps. Thanks Jay Late breaking news I went ahead and tried the fix by removing the U1 part of the touchpad. Don't use crazy glue!!! Report Gerry- Nov 22, 2009 at 07:33 PM Thanks Jim, same problem on Dell 1545 laptop Your solution worked ... http://www.techspot.com/community/topics/dell-inspiron-1100-wont-turn-on.37680/
contact these guys if you want some one else to do it. You can find replacement parts on eBay. The answer lay in the touchpad assembly removed for inspection (upon which the unit sprang into life - this is where the problem lay) I noticed where the magnet would exhert Is there any error beeps / led code for the Inspiron?
At some level today, a new console is cheaper than a repair. When I press the button the only thing that happens is the three lights blink. Please help! This is the switch that controls the stand by function when you close your lid.
That worked for me. Can you get to the BIOS? Once reported, our moderators will be notified and the post will be reviewed. useful reference because replacing memory did nothing.
All Rights Reserved. Either you get it, or you don't. 0 hughv 104 8 Years Ago Go to Dell and enter your service number to get the specs on your HD. The remove the four screws that hold the top attachment for the display to the laptop. Remember to push hard.
Remove the blue strip with a butter knife that covers the power button. http://techpatterns.com/forums/about1230.html Anyways, thanks for your tip :-) Helpful +129 Report naron Jul 13, 2010 at 12:37 PM *Take out the battery, *Remove main supply, *Hold power button down for 30 secs, *Put The floppy LED would flash about 8 or 9 times, then all the LEDs would go out and the charging LED would light. What should I do?
And remember, that deterioration happened while they were sitting undisturbed (until I checked them) in storage in their original shipping containers. navigate here Processor failure same procedure as problem 4 in first case above. Use Epoxy. Ask a question and give support.
U the man. In this case try with another charger or check AC adapter with a Multimeter. CAUTION: There SHOULD be a spacer on the Left screw hole of the power/charger board. http://xmailing.net/dell-inspiron/dell-inspiron-1100-memory.php The only LED on after that would perhaps be the battery charging indicator.
It's not my fault if you damage your laptop further. Solved the problem in 10secs - you are a star! By the way, do you have any suggestions as to where I might get a replacement HD if this happens again?
For example, if a strong rare-earth magnet is allowed to "clack" together with another magnet or a hard surface from just a couple of inches away, the brittle nickel-plating can be
Graphics Card failure same procedure as problem 7 in first case above. To do this gently put your fingernail under one of the end keys on the keyboard (Right arrow key, right shift, enter, \, backspace, Page down, Page up, Left ctrl, left Sep 6, 2007 #9 SimonEast TS Rookie Unfortunately it sounds like a more serious problem than the one I experienced. Unscrew the 8 or 9 screws on the underside of the laptop, including the one you can only reach by removing the battery 2.
Monty from mexico. Click here to become a Hardware Analysis registered user. Remove the screws on the bottom of the case. this contact form No = problem with lid sensor.
Yay! With a charger and fully-charged battery (checked the LEDs on the pack), pressing the power button would cause the power and hard drive LEDs to light. Nov 14, 2007 #14 wannabetech TS Rookie Thank you so much for this forum! john albrich May 08, 2011, 05:09pm EDT Reply - Quote - Report Abuse Private Message - Add to Buddy List Edited: May 08, 2011, 05:18pm EDT >>Subject: NON-destructive way to
like there is a short in the board in that area. Report Spray1969- Dec 19, 2009 at 09:11 AM This worked for me,wasnt getting beyond f1/f12 first page option so hit f1 (quickly,whilst option is on screen!).